For CCNA exam success, you had better know what split horizon is, how to turn it off, and when to turn it off. Knowing when to turn split horizon off is also important in production networks, because it can cause a hub-and-spoke network to have incomplete routing tables on the spokes. Split horizon exists for a very good reason - routing loop prevention. The rule of split horizon states that a router cannot send an advertisement for a route out the same interface that it came in on. Split horizon is on by default on all interfaces running RIP, IGRP, and EIGRP. In this CCNA tutorial, R1 will serve, as the hub and R2 and R3 will be the spokes. We'll first configure EIGRP over the 172.16.123.0 /24 network, the network connecting the three routers. R1#conf t R1(config)#router eigrp 100 R1(config-router)#no auto-summary R1(config-router)#network 172.12.123.0 0.0.0.255 R2#conf t R2(config)#router eigrp 100 R2(config-router)#no auto-summary R2(config-router)#network 172.12.123.0 0.0.0.255 R3#conf t R3(config)#router eigrp 100 R3(config-router)#no auto-summary R3(config-router)#network 172.12.123.0 0.0.0.255 Running show ip eigrp neighbor on R1 shows that adjacencies to R2 and R3 are up. R1#show ip eigrp neighbor IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (ms) Cnt Num 1 172.12.123.3 Se0/0 11 00:02:45 1 5000 0 1 0 172.12.123.2 Se0/0 161 00:03:01 1 5000 0 1 Each router will now advertise its loopback address via EIGRP. R1#conf t R1(config)#router eigrp 100 R1(config-router)#network 1.1.1.0 0.0.0.255 R2#conf t R2(config)#router eigrp 100 R2(config-router)#network 2.2.2.0 0.0.0.255 R3#conf t R3(config)#router eigrp 100 R3(config-router)#network 3.3.3.0 0.0.0.255 Running show ip eigrp route on each router shows that R1 has a route for both R2s and R3s loopback. R2 and R3 will only see R1s loopback address, and not each others. Why? R1#show ip route eigrp 2.0.0.0/24 is subnetted, 1 subnets D 2.2.2.0 [90/2297856] via 172.12.123.2, 00:03:19, Serial0/0 3.0.0.0/24 is subnetted, 1 subnets D 3.3.3.0 [90/2297856] via 172.12.123.3, 00:03:04, Serial0/0 R2#show ip route eigrp 1.0.0.0/24 is subnetted, 1 subnets D 1.1.1.0 [90/2297856] via 172.12.123.1, 00:03:40, Serial0/0.123 R3#show ip route eigrp 1.0.0.0/24 is subnetted, 1 subnets D 1.1.1.0 [90/2297856] via 172.12.123.1, 00:05:17, Serial0/0.31 EIGRP uses Split Horizon by default to prevent routing loops. In this lab, though, it prevents full network reachability. R2 and R3 both form neighbor relationships with R1s Serial physical interface. R2 advertises its loopback address to R1s Serial interface, as does R3. Split Horizon does not allow a route to be advertised back out the same interface it was received on. This prevents R1 from advertising R2s loopback to R3, or R3s loopback to R2. Split Horizon must be disabled to allow full network reachability in this lab. To do so, run no ip split-horizon eigrp 100 on R1s Serial interface. When Split Horizon is disabled, that will cause the neighbor relationships to fail, and then reestablish. Run show ip route eigrp 100 on both R2 and R3. The appropriate route to the remote loopback address will now appear. R1#conf t R1(config)#int serial0 R1(config-if)#no ip split-horizon eigrp 100 10:02:23: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.2 (Serial0/0) down: split horizon changed 10:02:23: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.3 (Serial0/0) down: split horizon changed 10:02:27: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.3 (Serial0/0) ip: new adjacency 10:02:54: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.2 (Serial0/0) ip: new adjacency R2#show ip route eigrp 1.0.0.0/24 is subnetted, 1 subnets D 1.1.1.0 [90/2297856] via 172.12.123.1, 00:00:06, Serial0/0.123 3.0.0.0/24 is subnetted, 1 subnets D 3.3.3.0 [90/2809856] via 172.12.123.1, 00:00:06, Serial0/0.123 R3#show ip route eigrp 1.0.0.0/24 is subnetted, 1 subnets D 1.1.1.0 [90/2297856] via 172.12.123.1, 00:00:12, Serial0/0.31 2.0.0.0/24 is subnetted, 1 subnets D 2.2.2.0 [90/2809856] via 172.12.123.1, 00:00:12, Serial0/0.31 Disabling split horizon should be done with care, but knowing when and where to do so shows that you truly understand how this technology works - and that's a big step on the way to earning your CCNA! |
About Us
